Pratter PLC: Machine controls e configuração Modbus RTU
O Rostoc é compatível com Pratter PLC?
Sim - Pratter PLC é compatível com o Rostoc via Modbus RTU over RS-485 serial (9600 baud). Esta máquina pode ser conectada para registro de dados de torra em tempo real, registro da Curve e análise da torra. Em contas elegíveis, o Rostoc também pode controlar as funções listadas abaixo.
Configuração de conexão
Pratter PLC se conecta ao Rostoc via Modbus RTU over RS-485 serial (9600 baud).Conexão: RS-485 Serial.
Passos de configuração
- Connect a USB-to-RS-485 adapter to your computer, then connect the adapter to the machine RS-485 port or terminals.
- Match the A/B or +/− wiring to the machine manual. If the adapter has ground, connect it only when the manual recommends it.
- Install the adapter driver if your operating system requires it.
- Open Rostoc and go to Settings → Machines.
- Click + Add Machine and choose Browse Catalogue.
- Find "Pratter PLC" in the catalog and click Add.
- Back on the main screen, click Use for the Machine if needed, then choose the serial port assigned to the adapter. The baud rate, serial settings, and unit ID are pre-filled from the catalog.
- Close other roasting software that may be using the same adapter.
- Click Connect to start reading data.
Solução de problemas
- Serial port not detected
- Ensure the USB-to-RS-485 adapter driver is installed. Try a different USB port. On macOS, check System Information > USB.
- No response from roaster
- Verify the baud rate and parity settings match the roaster's configuration. Check RS-485 wiring polarity (A/B or +/−).
- CRC errors in log
- Reduce cable length or add a termination resistor. Ensure no other device shares the RS-485 bus.
- Another app is open
- Close other roasting software that may be using the same serial adapter before connecting in Rostoc.
Controles da máquina
Contas elegíveis podem enviar estes comandos quando a máquina estiver conectada e selecionada. Teste com segurança antes do uso em produção.
Conexão: Pratter Pratter PLC · RS-485 Serial (USB)
Controles ajustáveis
| Controle | Como funciona | Valores de comando do Rostoc | Verificação do resultado |
|---|---|---|---|
| Fan SetpointSaída | Controle deslizanteAjustar e soltar | 0–100 % | Confirmação da conexão; verifique na máquina |
| Drum SpeedSaída | Controle deslizanteAjustar e soltar | 0–100 % | Confirmação da conexão; verifique na máquina |
| Burner SetpointSaída | Controle deslizanteAjustar e soltar | 0–150 % | Confirmação da conexão; verifique na máquina |
Estes são os valores de comando aceitos pelo Rostoc para esta conexão, não limites operacionais seguros certificados. Siga os limites e procedimentos do fabricante.
Consulte disponibilidade e segurança em Controles da máquina. Para navegar pelos controles sem o mouse, consulte Atalhos de teclado.
Especificações
| Tipo de torrador | Drum |
|---|---|
| Aquecimento | Unknown |
| Tipo de setup | Modbus |
| Conexão | RS-485 Serial (USB) |
Fluxos de dados
Quando conectado, o Rostoc lê os seguintes dados desta máquina:
- Bean Tempcelsius
- Env Tempcelsius
- Burner Setpointpercent
- Fan Setpointpercent
- Drum Speedpercent
Notas
BT uses slave 1 register 1000; ET uses slave 1 register 1001.