Pratter PLC: Machine controls dan setup Modbus RTU
Apakah Rostoc mendukung Pratter PLC?
Ya - Pratter PLC didukung oleh Rostoc via Modbus RTU over RS-485 serial (9600 baud). Mesin ini dapat dihubungkan untuk logging data roasting secara real-time, merekam Curve, dan analisis roasting. Untuk akun yang memenuhi syarat, Rostoc juga dapat mengontrol fungsi yang tercantum di bawah.
Setup koneksi
Pratter PLC terhubung ke Rostoc via Modbus RTU over RS-485 serial (9600 baud).Koneksi: RS-485 Serial.
Langkah setup
- Connect a USB-to-RS-485 adapter to your computer, then connect the adapter to the machine RS-485 port or terminals.
- Match the A/B or +/− wiring to the machine manual. If the adapter has ground, connect it only when the manual recommends it.
- Install the adapter driver if your operating system requires it.
- Open Rostoc and go to Settings → Machines.
- Click + Add Machine and choose Browse Catalogue.
- Find "Pratter PLC" in the catalog and click Add.
- Back on the main screen, click Use for the Machine if needed, then choose the serial port assigned to the adapter. The baud rate, serial settings, and unit ID are pre-filled from the catalog.
- Close other roasting software that may be using the same adapter.
- Click Connect to start reading data.
Pemecahan masalah
- Serial port not detected
- Ensure the USB-to-RS-485 adapter driver is installed. Try a different USB port. On macOS, check System Information > USB.
- No response from roaster
- Verify the baud rate and parity settings match the roaster's configuration. Check RS-485 wiring polarity (A/B or +/−).
- CRC errors in log
- Reduce cable length or add a termination resistor. Ensure no other device shares the RS-485 bus.
- Another app is open
- Close other roasting software that may be using the same serial adapter before connecting in Rostoc.
Kontrol mesin
Akun yang memenuhi syarat dapat mengirim perintah ini saat mesin terhubung dan dipilih. Uji dengan aman sebelum penggunaan produksi.
Koneksi: Pratter Pratter PLC · RS-485 Serial (USB)
Kontrol yang dapat disesuaikan
| Kontrol | Cara kerja | Nilai perintah Rostoc | Pemeriksaan hasil |
|---|---|---|---|
| Fan SetpointOutput | SliderSesuaikan lalu lepaskan | 0–100 % | Dikonfirmasi oleh koneksi; verifikasi pada mesin |
| Drum SpeedOutput | SliderSesuaikan lalu lepaskan | 0–100 % | Dikonfirmasi oleh koneksi; verifikasi pada mesin |
| Burner SetpointOutput | SliderSesuaikan lalu lepaskan | 0–150 % | Dikonfirmasi oleh koneksi; verifikasi pada mesin |
Ini adalah nilai perintah yang diterima Rostoc untuk koneksi ini, bukan batas operasi aman yang tersertifikasi. Ikuti batas dan prosedur produsen mesin.
Pelajari ketersediaan dan keamanan di Kontrol mesin. Untuk berpindah kontrol tanpa mouse, lihat Pintasan keyboard.
Spesifikasi
| Tipe roaster | Drum |
|---|---|
| Pemanasan | Unknown |
| Tipe setup | Modbus |
| Koneksi | RS-485 Serial (USB) |
Aliran data
Saat terhubung, Rostoc membaca data berikut dari mesin ini:
- Bean Tempcelsius
- Env Tempcelsius
- Burner Setpointpercent
- Fan Setpointpercent
- Drum Speedpercent
Catatan
BT uses slave 1 register 1000; ET uses slave 1 register 1001.